Interconnection between the solidification and precipitation hardening processes of an AlSiCu alloy

Horizontal directional solidification and precipitation hardening experiments were performed with the Al5.5Si3Cu alloy. Solidification thermal and microstructural parameters such as growth and cooling rates (V_L and T_R, respectively) and the secondary dendrite arm spacing (λ₂) were determined experimentally. As-solidified samples were selected and submitted to the T6-heat treatment (T6-HT). The T6-HT was carried out considering two solution times: 8 and 5?h at 490?±?2°C, followed by quenching in warm water (60?±?2°C), aging for 5?h at 155?±?2°C and air-cooling. Higher HV values were observed for the solution time of 5 h. As highlights of this work, the influence of the processing parameters (V_L, T_R and λ₂) on the distribution, morphology and size of the eutectic Si particles has been investigated.     

Gd-Bi-M-Ce-O (M = Cu,Zr, Ni,Co, Mn) ceria-based solid solutions for low temperature CO oxidation

Ceria based solid solutions doped by Gd, Bi, and the third dopant were synthesized by the co-precipitation method with ultrasonic treatment, followed by calcination at the temperature of 500°С. Characterization of the synthesized nanosystems by XRD, TEM, TG, Raman spectroscopy, FTIR, XPS was carried out. It is shown that all obtained powders of solid solutions crystallized into a cubic structure of the fluorite type, with an average particle size of 5–15 nm. The samples had a mesoporous structure of the pore diameter of 2–5 nm. The catalytic activity of Gd-Bi-M-Ce-O (M = Cu, Zr, Ni, Co, Mn) solid solutions was carried out. The catalyst Gd_0.05Bi_0.15Mn_0.20Ce_0.60O₂ has the lowest oxidation temperature.     

Light stability in cyan and magenta tones using standard and highly chromatic toner particles

An increasing requisite regarding the reproduction quality of electrophotographic printing machines demands improvement of new electrophotographic toner formulation, especially used pigments. The subject of this paper is a comparison of prints realised by depositing high chroma (HC) and standard emulsion aggregation (EA) toner on gloss fine art paper. HC toner has a different composition of the cyan and magenta tones compared with the corresponding standard EA toner tones and therefore behaves differently under real conditions. The patches used for this experiment were cyan and magenta tone prints with tone values (TVs) of 0, 20, 60 and 100%. Ultraviolet (UV) degradation was measured over time intervals of 0, 6, 12, 24, 48, 96, 144 and 240 h for all patches. Results (laboratory values) were calculated using colorimetric difference. Values were plotted as a function of time in tonal degradation graphs. A model was created using non‐linear regression‐based modelling. The experiment demonstrates that magenta patches are more susceptible to degradation in comparison with cyan patches. With the increase in tonal value, it is noticeable that the colorimetric difference is higher. Colorimetric differences calculated using HC magenta toner and standard EA cyan toner (100% TV) were higher than ?E = 5, starting to appear after 6 h of exposure to UV radiance. After 12 h of exposure, colorimetric differences of standard magenta tones that were greater than ?E = 5 also started to appear. Cyan patches (100% TV) printed with HC toner were more stable than the other patches, and after 240 h of exposure had not crossed the boundary of ?E = 5.     

Polytetrafluorethylene-based high-k composites with low dielectric loss filled with priderite (K1.46Ti7.2Fe0.8O16)

Composite materials with a high permittivity (high-k) and low dielectric loss represent an important research direction for the rapid development of modern electronic. This article is about high-k composite with low dielectric loss (dielectric constant is approximately 11, and dielectric loss is only 0.02 at 1 MHz and about 50 wt % of filler) based on a polytetrafluorethylene (PTFE) compounded with priderite (K_1.46Ti_7.2Fe_0.8O₁₆). The dielectric permittivity about ε' ≈ 10³ and the dielectric loss of tgδ ≈ 2 have been found for filler content about 50 wt % (30 vol %) and, respectively, ε' ≈ 11 and tgδ ≈ 0.02 for 1 MHz. To produce filler, amorphous potassium polytitanate was synthesized by molten salt method, modified in aqueous solution of iron sulfate, crystallized at 700 °C and further treated in the aqueous dispersion of PTFE. The obtained product was pressured, dried and investigated by X-ray diffraction and scanning electron microscopy. Dielectric properties of the composite with different ceramic filler content (1–90 wt %) were studied using impedance spectroscopy in the frequency range of 10⁻² to 10⁶ Hz. The influence of frequency on electric conductivity, permittivity, and dielectric losses was analyzed taking into account the experimental data on porosity, apparent density obtained for the composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48762.     

“Arbequina” Olive Oil Composition Is Affected by the Application of Regulated Deficit Irrigation during Pit Hardening Stage

Three new regulated deficit irrigation (RDI) treatments were applied to “Arbequina” olive orchards during pit hardening. Oil quality was determined by measuring analytical parameters for olive oil grading, antioxidant activity, total phenol content, fatty acid profile, volatile compounds profile, and sensory analysis. Oils from RDI were classified as “extra virgin olive oil” and their quality was improved due to their higher antioxidant potential (ABTS⁺ [increased ~75%] and DPPH^˙ [increased ~25%] assays) and phenols (increased ~53%) than control. Concentration of total volatile compounds decreased (~27%) but RDI olive oils showed a more balanced profile (alcohols, aldehydes, and esters). Monounsaturated fatty acid content increased (~5%) and atherogenic and thrombogenic indexes decreased (~8.5%) in RDI olive oil. Regarding sensory analysis, RDI provided more balanced oils with higher fruit aroma than control. Other benefits of RDI olive oil, when compared with oil from full irrigated orchards are reduced use of water and improved functional and sensory quality.     

Production of stable amorphous form by means of spray drying

Spray drying is a very useful method for manufacturing of amorphous solid materials. This is mainly due to the possibility of fast solvent evaporation that leads to a rapid transformation of solution to a solid state. Besides evaporation kinetics, there are various process parameters that influence physical and chemical characteristics of such obtained material. The possibility of obtaining a stable amorphous structure of the active pharmaceutical ingredient in a spray dryer was examined. A solution of the hydrochloride crystalline structure of the active pharmaceutical ingredient in a mixture of water and acetonitrile was dried at different temperatures and flowrates of nitrogen used for atomization, as well as the flowrates of the solution. The influence of the process conditions on the properties of the product was analyzed. The final dried products were characterized and identified with a variety of analytical and physical methods. The results showed that a stable amorphous structure of the high purity active pharmaceutical ingredient is obtained, and that the optimal conditions of the process are defined. The amorphous structure is stable at temperatures below 200°C when it is transformed into a new crystal structure. Conditions of high relative air humidity lead to partial transformation.     

Special Important Aspects of the Thomson Effect

A comprehensive study of the mechanisms of heating and cooling originating from an electrical current in semiconductor devices is reported. The variation in temperature associated with the Peltier effect is not related to the presence of heat sources and sinks if the heat flux is correctly determined. The Thomson effect is commonly regarded as a heat source/sink proportional to the Thomson coefficient, which is added to the Joule heating. In the present work, we will show that this formulation of the Thomson effect is not sufficiently clear. When the heat flux is correctly defined, the Thomson heat source/sink is proportional to the Seebeck coefficient. In the conditions in which the Peltier effect takes place, the temperature gradient is created, and, consequently, the Thomson effect will occur naturally.